What drives can be installed?
The instruction manual spelled out all the parameters, both recommended for installation of disks, and acceptable replacement options. The correct choice of discs is impossible without following these recommendations and tolerances.
The use of standard wheel sets and the observance of the operating rules meets all the requirements for the safety and ease of use of the car. But if there is a desire to go beyond the standard characteristics, to change the dynamics indicators or to tune the RAV4, then it makes sense to equip it with a non-standard set of wheels. Such a replacement will affect the following characteristics:The steering response will change.
Tire adhesion and wear.
Noise level.
Fuel consumption.
Titanium and aluminum wheels weigh less than their steel counterparts. This has a direct impact on improving handling and reducing fuel consumption. The dimensions of the tires are interrelated with the parameters of the wheel used. Wide tires are good when driving on dry urban asphalt. But in bad weather conditions or in the winter season, they are more susceptible to side skids and aquaplaning.
Toyota RAV4 2.4i 2011 parameter values:
Tire dimensions: 225/65 R17. 225 – width of the tire in millimeters, 65 – ratio of the height of the tire’s cross-section to its width, R17 – tire diameter in inches.
Car wheel dimensions: 7 x 17 ET45, 7 – disc rim width in inches, 17 – disc rim diameter in inches, ET45 – disc offset: distance between the wheel disc mounting plane and the rim symmetry plane, mm.
PCD (Drilling): 5 114.3 – bore, number of mounting holes diameter of the circle of the centers of the holes, measured in mm.
Dia (Diameter): 60.1 – the diameter of the center hole for the hub, measured in mm.
Toyota RAV4 III (XA30) Facelift 2011 2.5
Sales market: American Domestic Market (USDM)
Generation: III (XA30) Facelift
Engine: I4, Petrol
Power: 181 hp (133 kW)
Wheel bolt pattern | |
PCD (number of holes x circle diameter) | 5×114.3 мм |
Center hole diameter (DIA) | 60.1 мм |
Fasteners | M12 x 1.5 |
Fastener type | Nut |
Tires | Disks | PCD | Dia | Pressure |
|
|
| ||
215/70 R16 99H Factory kit | 6.5Jx16 ET45 | 5×114.3 | 60.1 | 2.2 |
225/65 R17 101H Tuning | 7Jx17 ET45 | 5×114.3 | 60.1 | 2.2 |
235/55 R18 99H Tuning | 7.5Jx18 ET45 | 5×114.3 | 60.1 | 2.2 |
235/55 R18 99H Tuning | 7.5Jx18 ET39 | 5×114.3 | 60.1 | 2.2 |
What wheel sizes are recommended by the manufacturer?
The basic configuration of the Toyota RAV4 III (XA30) Facelift 2011 2.5 is fitted with 6.5Jx16 ET45 wheels assembled with 215/70 R16 99H tires. Where:
6.5J is the width of the rim in inches;
16 “- rubber landing diameter in inches;
ET45 – disc offset in millimeters.
Vehicle tire marking 215/70 R16 is deciphered as follows:
215 – width of the profile (cross-section of the tire) in millimeters;
70 – profile height as a percentage of its width;
R – radial cord winding;
16 is the landing diameter of the tire in inches.
In addition, the rubber can be marked with information about its carrying capacity and speed parameters – load index and speed index. The load index is a two-digit or three-digit number, the speed index is indicated by Latin letters, for example 99H:
99 – the maximum permissible tire load 775 kg;
H – the maximum permissible vehicle speed is 210 km / h.
Using the recommended tire sizes will avoid handling, safety and other issues. What non-standard sizes can be supplied? Follow the data in the table, it shows the possible admissible alternative dimensions for tuning. Although other options are possible that we have not described in the table. For example, discs are wider with the same diameter. Or put discs of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge, you can find copies with the same parameters, but with an overhang of 1-2 millimeters more or less. It is not possible to list all the options.
In this case, the bolt pattern for all types of wheels is the same – 5×114. 3. Thus, all the discs are mounted on five bolts and the distance between them is exactly one hundred and fourteen point and 30 hundredths of a millimeter. The diameter of the car hub is 60.1 mm.
Standard tire pressure – 2.2 Mpa
Toyota RAV4 III (XA30) Facelift 2011 3.5
Sales market: American Domestic Market (USDM)
Generation: III (XA30) Facelift
Engine: V6, Petrol
Power: 272 hp (200 kW)
Rim bolt pattern PCD (number of holes x circumference) 5×114.3 mm
Center hole diameter (DIA) 60.1 mm
M12 x 1.5 fastener
Fastener Type Nut
Tires | Disks | PCD | Dia | Pressure |
225/65 R17 101H Factory kit | 6.5Jx17 ET45 | 5×114.3 | 60.1 | 2.2 |
225/65 R17 101H Tuning | 7Jx17 ET45 | 5×114.3 | 60.1 | 2.2 |
235/55 R18 99H Tuning | 7.5Jx18 ET45 | 5×114.3 | 60.1 | 2.2 |
235/55 R18 99H Tuning | 7.5Jx18 ET39 | 5×114.3 | 60.1 | 2.2 |
What wheel sizes are recommended for RAV4 Facelift 2011 3.5
The basic configuration of Toyota RAV4 III (XA30) Facelift 2011 3.5 is fitted with 6.5Jx17 ET45 wheels with 225/65 R17 101H tires. Where:
6.5J is the width of the rim in inches;
17 “- rubber rim in inches;
ET45 – disc offset in millimeters.
Vehicle tire marking 225/65 R17 is deciphered as follows:
225 – width of the profile (cross-section of the tire) in millimeters;
65 – profile height as a percentage of its width;
R – radial cord winding;
17 is the landing diameter of the tire in inches.
In addition, the rubber can be marked with information about its carrying capacity and speed parameters – load index and speed index. The load index is a two-digit or three-digit number, the speed index is denoted by Latin letters, for example 101H:
101 – the maximum permissible tire load 825 kg;
H – the maximum permissible vehicle speed is 210 km / h.
Using the recommended tire sizes will help you avoid handling, safety and other issues. What non-standard sizes can be supplied? Follow the data in the table, it shows the possible admissible alternative dimensions for tuning. Although other options are possible that we have not described in the table. For example, discs are wider with the same diameter. Or put discs of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge, you can find copies with the same parameters, but with an overhang of 1-2 millimeters more or less. It is not possible to list all the options.
In this case, the bolt pattern for all types of wheels is the same – 5×114. 3. Thus, all discs are mounted on five bolts and the distance between them is exactly one hundred and fourteen point and 30 hundredths of a millimeter. The diameter of the hub for a car is 60.1 mm.
The standard tire pressure is 2.2 MPa.
General background information
Ranges of possible values for tires and wheels Toyota RAV4 2011.
Tires Diameter 16 “-18”
Width (mm) 215-235
Profile (%) 55–70
Smallest size 215/70 R16
Largest size 235/55 R18
Wheels Diameter 16 “-18”
Width (inches) 6.5-7.5
Reach (mm) 39–45
Drilling 5×114.3
Expert advice
When choosing rubber for a car, you must first of all follow the manufacturer’s instructions. Ask yourself a few questions.
What roads will the car be used primarily on?
Do you need increased cross-country ability?
How much of the route will be city roads, and what route?
Will the car carry heavy loads?
The answers to these and similar questions will help determine which tire parameters need to be paid special attention.
How to choose the right wheels for Toyota RAV4 2011?
3 types of rims Toyota 2011 RAV4
Stamped (economical price category) – are made of iron sheet by stamping on a press.
Light alloy – made by “casting” (more reliable than stamped).
Forged (the highest quality and more expensive than the previous ones) – are made of light alloys by stamping at high temperatures.
The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface, on which you have to drive every day, must also be considered.
So, when it gets into a hole, the stamped disc will bend and not harm the tire, and the forged or cast disc can cut it. There is a possibility that the alloy wheel could burst or crack.
It should also be noted that repairing “stamping” is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less. lighter and more perfect geometry (better balanced).
The same disks can rub with tires or not rub on the same car – here the “wheel alignment” adjustment will help.
What is the tire pressure?
It is the driver’s responsibility to constantly monitor the tire pressure. This will avoid common problems associated with vehicle operation. A non-nominal pressure value often causes:
deterioration in management;
uneven tread wear.
Often the car owner independently reduces the pressure in the wheels of his own vehicle. Thus, the load on the suspension is reduced, the car “passes” various unevenness of the road much easier. But it is worth noting: lowering the pressure even by 0.1 MPa leads to serious problems. The main ones include:
increased fuel consumption;
rapid wear of the extreme tread segments;
the car becomes less maneuverable.
An over-pumped wheel is no less problematic. The central part of the balloon begins to grind down quickly. In addition, at an ambient temperature of more than 60 degrees Celsius, the tire may simply explode. Which will lead to leaving the oncoming lane.
What disks can be put on Toyota RAV4?
The abbreviation in the name of the crossover “RAV” means that the car is intended for recreation and hiking. “4” – four-wheel drive. There are special requirements for the wheels of such machines. What disks are:
Stamped – the most common option, comes in the basic configuration of the Toyota RAV4. They do not crack when they fall into the pit, and if they bend, they can be easily repaired. Such discs are made of steel. The disadvantage is a lot of weight. And the unsightly appearance is covered with caps.
Cast light-alloy – weight less than stamped, made of aluminum and magnesium alloy. When they fall into the pit, they crack, it will not be possible to restore. Outwardly, they are attractive, the manufacturing technology helps to give them any shape. The heat-conducting material cools the braking system well. Alloy wheels are more expensive than stamped ones.
Forged – lightweight and durable. Do not split when the wheel hits the pit. But all the impact energy falls on the suspension. Configuration choices are limited by manufacturing technology. The cost is at the level of light-alloy analogues.
Wheels are selected for the car according to the characteristics recommended by the manufacturer. The car suspension is designed for rims, therefore, all parameters are observed.
The technical data sheet indicates the “native” and acceptable options. Car owners on RAV4 take larger tires. Discs are of a different diameter, a different offset value, a smaller tire width. But PCD must not be violated: the mounting holes of the discs and the car must match perfectly. When choosing new discs, make sure that the CO (central hole of the discs) coincides with the factory one.
Parameters of standard nuts
In the basic configuration Toyota RAV4 alloy wheels are fastened with studs and nuts. This is not a universal fastener; it is replaced with M12x1.25 threaded bolts.
When they are used to replace the rims, it is observed that the parameters of the discs (old and new) match. If you change the stamped disc to a cast one, use longer fasteners, whether they are bolts or studs. Cast products are thicker than steel. Also follow the contours of the recess in the holes of the disc. They should fit perfectly to the mounting surface of the fastener. It is located immediately under the head of bolts and nuts, it can be tapered or spherical.
